Why Is My Fiberglass Pool Bubbling? Blisters, Osmosis, and Repair Options

Fiberglass Pool Blisters

In this article

Finding raised bubbles on the floor or walls of a fiberglass swimming pool can be unsettling, even when the water looks clear. They may be small, form visible domes, or appear beside earlier repairs.

The short answer is that fiberglass pool blisters can develop when moisture collects beneath the gelcoat, often through a process called osmosis. But a failing paint layer, a manufacturing defect, or movement of the pool shell can produce similar-looking symptoms. The right repair depends on the damaged layer and the condition of the fiberglass underneath. Blisters do not automatically mean you need a new pool.

Are the Bubbles in the Fiberglass Surface or in the Pool Water?

First, look at what is actually bubbling. If tiny air bubbles are streaming from a return jet or gathering on the water’s surface, that is different from a raised spot you can see and feel in the pool wall. Air entering the circulation system can create bubbles in the water without damaging the fiberglass finish.

Surface blisters stay in the same place. They may look like little rounded bumps, swollen patches, or larger raised sections of gelcoat. They appear on steps, floors, or walls and may feel hard or slightly flexible. Appearance alone cannot tell you whether the separation is only in the finish or goes deeper into the fiberglass laminate.

How Osmosis Causes Blisters in Fiberglass Pools

A fiberglass pool shell is made from layers of reinforcing fiberglass and resin, with a colored gelcoat forming the smooth interior finish. Gelcoat provides a useful protective layer, but many traditional polyester-based systems are not completely impermeable to water. Moisture can migrate through the finish, especially where microscopic defects or voids exist.

If that moisture reaches pockets containing water-soluble substances, those substances dissolve and create a concentrated solution. Osmosis encourages more water to move toward that solution. As liquid accumulates in a confined space, pressure can push the gelcoat outward and form a blister. Hydrolysis, a reaction between water and susceptible resin components, can further damage the laminate.

This mechanism is described in WEST SYSTEM’s technical guide to gelcoat blisters. Although the guide focuses on boats, the material behavior also applies to fiberglass pools. A blister sometimes contains fluid with a sharp or acidic odor; that is a possible clue, not something a homeowner should puncture a bump to investigate.

Other Reasons a Fiberglass Pool May Look Bubbled

Old pool paint can lift from the surface. If a fiberglass pool was painted previously, bubbles may form within the paint or at the bond between the paint and underlying gelcoat. Poor preparation, moisture, or incompatible materials can affect adhesion. Peeling paint does not necessarily prove that the underlying shell has osmotic damage, although both problems can exist together.

Voids or defects may be present in the original material. Trapped air, incomplete wetting of fiberglass reinforcement, or other manufacturing irregularities can contribute to blister formation. The visible finish may conceal such defects for years.

A large bulge can be a different problem altogether. A broad hump in the floor, a wall that has changed shape, or an area that flexes underfoot may involve shell movement, support problems, or outside groundwater pressure. These symptoms need prompt assessment, not another cosmetic coating.

Are Fiberglass Pool Blisters Serious?

Not every blister is an emergency. A small number of isolated, intact bumps on an otherwise firm pool surface may be suitable for monitoring or localized repair after assessment. Appearance cannot establish whether moisture has reached the laminate, and blisters can exist without a visible leak.

Widespread blistering, clusters that continue to develop, cracked or leaking blisters, and areas where the finish is separating are more concerning. So are deep cracks, soft fiberglass, a springy floor, unexplained water loss, or changes in the shape of the shell. These signs may involve the laminate itself. Avoid swimming if the surface has sharp exposed fibers, unstable steps, or damage that may create an injury risk, and arrange an inspection.

The important distinction is between surface damage and structural damage. Gelcoat damage can often be repaired without replacing the shell. Deteriorated fiberglass reinforcement or loss of support may require a different repair plan and, in some cases, a structural specialist. Nobody can make that distinction confidently from one photograph.

What Should You Do When You Notice the First Blisters?

Take clear photographs, including a wider view that shows where each affected area sits in the pool. Record when they appeared and whether the pool has been painted or repaired. Photograph the same spots over time. That record is more useful than guessing how quickly a blister is growing.

Do not cut, puncture, sand, or aggressively scrub the raised areas to see what is inside. Opening a blister can expose damaged material and complicate a later repair. Do not use putty or paint to conceal an undiagnosed problem. If the pool is relatively new, contact the shell manufacturer or installing builder about warranty inspection requirements before authorizing invasive work.

Most importantly, do not drain an in-ground fiberglass pool on your own to inspect the damage. Emptying the pool changes the pressure acting on the shell, and that can create a much larger problem than the original blisters.

How a Professional Diagnoses Bubbling and Osmosis

Diagnosis begins with the pool’s history and damage pattern. A contractor should ask about age, earlier coatings, spreading bumps, leaks, and past repairs. An isolated step defect differs from widespread wall and floor blisters.

Next comes an assessment of the finish and, where accessible, the layers beneath it. A professional may examine whether a raised area is in old paint, original gelcoat, or the laminate itself. Sounding, moisture checks, and carefully opening representative defects may be appropriate as part of a controlled repair assessment. Moisture readings are relative indicators, not definitive proof of osmosis.

If deeper delamination, abnormal movement, or significant cracking is suspected, surface refinishing should not be the first step. The shell’s condition and any underlying support or groundwater issue must be understood before a coating is selected. Ask what is known, what remains uncertain, and whether hidden repairs are included in the quote.

Fiberglass Pool Blister Repair Options

Localized Blister Repair

When only a few areas are affected and the surrounding laminate is sound, targeted repair may be reasonable. The damaged material is opened and removed as needed, the area is cleaned and dried to the repair system’s requirements, and compatible fiberglass or gelcoat materials are used to restore the surface. Color matching may be imperfect, and a patch cannot prevent unrelated blisters elsewhere.

Wider Repair and Resurfacing

If blisters cover much of the interior, repairing each one separately may no longer be sensible. The job may require removing failed gelcoat or coatings over a larger area, assessing the laminate, cleaning out affected material, allowing adequate drying, and rebuilding damaged sections. Only then should a new finish be installed. Covering active moisture damage is not a substitute for repair.

Repairing Failed Paint or an Earlier Coating

Where the visible bubbles are in a previous coating, the contractor needs to establish how much material is poorly bonded and whether the original gelcoat is still serviceable. Preparing directly over loose paint invites another failure. The material and extent of coating failure determine how much removal is necessary.

Structural Fiberglass Repair

If inspection reveals significant laminate separation, deep cracks, or sections that flex abnormally, a cosmetic patch or resurfacing treatment is not enough. Damaged fiberglass may need to be removed and rebuilt with appropriate reinforcement, and any support or water-pressure problem addressed. Replacement may be considered for severe damage, not simply because blisters are visible.

Can ecoFINISH polyFIBRO Help a Blistered Fiberglass Pool?

For a fiberglass pool with a repairable shell, a new interior coating may be part of the restoration. At SC Pool Resurfacing, we offer fiberglass pool resurfacing with ecoFINISH polyFIBRO, a thermally applied polymer finish intended for fiberglass surfaces. The manufacturer describes a smooth, repairable finish that can be refilled promptly after application.

The coating does not replace the need to address moisture damage, failed paint, cracks, or unsound laminate beforehand. Repair and preparation come before resurfacing. We assess pool surface repair needs before recommending a finish, and some pools may be better served by localized work rather than complete resurfacing. Any proposed warranty should be reviewed in writing for its actual coverage and exclusions.

Why Charleston Homeowners Need to Be Careful About Draining

Charleston, Mount Pleasant, Johns Island, James Island, Daniel Island, and surrounding Lowcountry communities include properties where groundwater conditions can be an important part of pool work. After heavy rain or where groundwater sits high, pressure outside an emptied fiberglass shell can cause a wall to bow or, in extreme cases, lift the pool. A coastal address does not prove the cause of a blister.

Engineering guidance on hydrostatic pool failures explains this risk. Before a fiberglass pool is drained for inspection or resurfacing, the contractor needs to consider site conditions and the shell manufacturer’s guidance. Avoid turning a manageable surface problem into a structural one through an unnecessary DIY drain.

How Much Does Fiberglass Blister Repair Cost?

There is no reliable flat price for a blister repair without seeing the pool. Isolated defects differ substantially from laminate repairs or extensive paint removal. Access, pool size, groundwater precautions, material selection, and the condition revealed during preparation also affect the estimate.

Ask for an itemized explanation of surface preparation, anticipated fiberglass repairs, the proposed finish, drainage precautions, and refill or startup responsibilities. Find out what happens if hidden damage appears after work begins and how any additional costs would be approved. Drying or structural repairs can extend a project well beyond coating application. Be cautious of a guaranteed turnaround given before the underlying damage has been assessed.

Can You Prevent Fiberglass Pool Blisters?

Good maintenance helps protect a fiberglass finish, but it cannot correct every manufacturing defect or eliminate all moisture movement within a laminate. Follow manufacturer water-chemistry instructions, avoid concentrated chemicals sitting on the finish, and address chips or cracks early. Keep records of repairs and avoid covering an unknown finish with another coating without checking compatibility.

If bubbles are already present, prevention means understanding and repairing the cause rather than hiding the symptom. An early evaluation may leave more options available than waiting for blisters to spread, burst, or expose deeper damage.

Frequently Asked Questions

Can I Keep Swimming if My Fiberglass Pool Has Blisters?

A few intact surface blisters do not automatically make the water unsafe, but the pool should be assessed if the damage is new or spreading. Do not use areas with sharp exposed fiberglass, unstable steps, significant cracking, or suspected structural movement. Swimming safety also depends on normal water quality and equipment conditions, which are separate from the finish.

Will Fiberglass Pool Blisters Go Away on Their Own?

A blister may change shape, but that does not mean the underlying defect has healed. A bubble that looks flatter later can still indicate separation or damage beneath the gelcoat. Monitoring may be appropriate in limited cases; a repair recommendation requires diagnosis.

Can I Fix the Blisters With Epoxy Putty or Pool Paint?

Putty may suit a specific localized repair, but covering a bubble does not remove damaged or wet material beneath it. Some failures involve the bond of an existing coating, while others involve the fiberglass itself. The repair method must match the problem, and product compatibility matters.

Does Osmotic Blistering Mean My Fiberglass Pool Is Leaking?

Not necessarily. Fluid can accumulate within the gelcoat or laminate without creating a through-shell leak. On the other hand, falling water levels, active cracks, or wet areas around the pool need separate investigation. SC Pool Resurfacing focuses on the pool surface; plumbing and leak-detection problems may require a different specialist.

Get a Clear Answer Before Choosing a Repair

If you have noticed blisters, swollen patches, or peeling on your fiberglass pool in Charleston or the surrounding Lowcountry, start with an assessment rather than assuming you need to replace the shell. SC Pool Resurfacing offers free on-site pool evaluations and can discuss whether surface repair or fiberglass resurfacing is suitable for the condition found. Request a free estimate or call 854-444-9416 to have the surface evaluated before the problem becomes harder to address.

Have a question about your pool?

Tell us what you’re seeing and we’ll get back to you.

Facebook
Twitter
LinkedIn
Email

Get a free estimate

Tell us a little about your pool and we’ll get back to you.

Prefer to talk?

Recent posts